New for 2022. 100% Oznium exclusive. Designed from the ground up, to be bright, and sleek.
The applications are endless. The only limit is your imagination. You can use them for architectural accents, indoors, outdoors, in walkways, in railings, decks, etc. Use them for car lighting, in the front of your car, back of your car, or even inside your car. Use them for marine or industrial applications; UL Listed and RoHS compliant also! Not only does the CNC'ed billet aluminum housing look cool, it also acts as a heat sink for the high power LED.
Super easy to install. Just drill an appropriate sized hole, feed the wires, and LED bolt through. Tighten the matching nut from the back side, and everything will stay in place. Connect the wires to any 12 volt power source.
All of our LED bolts are IP68 certified fully waterproof.
High Intensity Flush Mount LED Bolt, UL Listed
Flush Mount LED Bolt has been tested and certified by UL, a nationally recognized safety and sustainability standard. UL Listed Certification E521307
If you're looking for a small but bright LED light, these are what you need. With various colors available, flush mountable and extremely low profile design, our LED bolts can be used in a wide range of applications.
Want the best brightness possible? Choose the 3W version which packs a powerful punch of triple 3X the lumen
The "With Lens" version projects a 60 degree powerful spotlight, while the "No Lens" projects a wide 180 degree flood light
3 different sizes to choose from (6mm, 11mm & 16mm)
Every LED bolt comes pre-wired with 3 feet of wire.
The stainless steel version comes with a high quality marine grade cable, double epoxy sealed top and bottom and shorter housing.
We use epoxy to seal both the top and bottom of the 1W Stainless Steel bolt.
Related Accessories
Fade-in Fade-out LED Dimmer
Smooth Fading Effect for Soft Start and Stop
Dual Intensity Brake Light Driver
Let Your Additional LEDs with Dual Intensity Function
Switchback LED Driver
Perfect for Switching LED Colors
Mini LED Dimmer Knob
With a simple turn of the knob, you can dim down, or brighten up your LEDs
Drill Bit
Buy them conveniently from us in various sizes to match the diameter of your LED Bolts: 6mm, 11mm, and 16mm.
Rubber O-Ring
For a water-tight seal around the bolt bezel and your panel.
Replacement Nuts
Need more nuts? You can buy extras.
DC Barrel Jack Adapter
These adapters allow you to convert your plug / jack / wires to each other.
Wire Splice Connector
A quick and easy way to splice LED wires together for your lighting project.
2 Core Marine Cable
Used for connecting LED strips or pretty much any other LED product, and extending wires.Customers Also Viewed
Flush Mount LED Bolt Photos & Videos
Action Shots
Product review & unpacking from a satisfied Oznium.com customer:
Flush Mount LED Bolt Technical Info
| Dimmable | Yes |
| IP Rating | IP68 fully waterproof / submersible |
| Polarity Sensitive | Yes |
| Operating Voltage Range | 12 VDC |
| Operating Temperature | Below 113F / 45C |
| Wire Gauge | 22AWG |
| Wire Length | 3.3 feet / 1 meter |
| Housing Material | Aluminum / Stainless Steel |
| Lens Material | PMMA |
| Beam Angle | With Lens : 60 degree Without Lens: 180 degree |
| Thread Size | M6 x 1, M11 x 1, M16 x 1 (Metric) |
| Thread Angle | 60 degree |
| Drill Hole Sizes | 6mm, 11mm, 16mm (15/64", 7/16", 5/8") |
| Weight | Aluminum 6mm: 6g 11mm: 16g 16mm: 24g Stainless Steel 32g |
| Certifications | cULus Listed Certification E521307 |
| Documents | Dimensional Drawing 6mm Aluminum Without Lens 11mm Aluminum Without Lens 11mm Aluminum With Lens 11mm Stainless Steel Without Lens 16mm Aluminum Without Lens 16mm Aluminum With Lens |
| Part No | Diameter | Wattage | Housing | LED Color | CCT(K) / Wavelength(nm) | Lumen(lm) | Current @12VDC (mA) |
|---|---|---|---|---|---|---|---|
| 2432 | 6mm | 0.5W | Aluminum | Cool White | 9000K+ | 5 | 18 |
| 3455 | 6mm | 0.5W | Aluminum | Neutral White | 6000-6500K | 5 | 18 |
| 2433 | 6mm | 0.5W | Aluminum | Warm White | 3000-3200K | 6 | 18 |
| 2435 | 6mm | 0.5W | Aluminum | Red | 625 | 3 | 18 |
| 2437 | 6mm | 0.5W | Aluminum | Green | 525 | 6 | 18 |
| 2434 | 6mm | 0.5W | Aluminum | Blue | 470 | 1 | 18 |
| 2436 | 6mm | 0.5W | Aluminum | Amber | 595 | 2 | 18 |
| 2229 | 11mm | 1W | Aluminum | Cool White | 9000K+ | 33 | 40 |
| 3453 | 11mm | 1W | Aluminum | Neutral White | 6000-6500K | 33 | 40 |
| 2230 | 11mm | 1W | Aluminum | Warm White | 3000-3200K | 33 | 40 |
| 2225 | 11mm | 1W | Aluminum | Red | 625 | 12 | 40 |
| 2227 | 11mm | 1W | Aluminum | Green | 525 | 25 | 40 |
| 2226 | 11mm | 1W | Aluminum | Blue | 470 | 4 | 40 |
| 2228 | 11mm | 1W | Aluminum | Amber | 595 | 8.5 | 40 |
| 3188 | 11mm | 1W | Aluminum | UV | 410 | 0.25 | 40 |
| 2217 | 16mm | 1W | Aluminum | Cool White | 9000K+ | 33 | 40 |
| 3449 | 16mm | 1W | Aluminum | Neutral White | 6000-6500K | 33 | 40 |
| 2218 | 16mm | 1W | Aluminum | Warm White | 3000-3200K | 33 | 40 |
| 2213 | 16mm | 1W | Aluminum | Red | 625 | 12 | 40 |
| 2215 | 16mm | 1W | Aluminum | Green | 525 | 25 | 40 |
| 2214 | 16mm | 1W | Aluminum | Blue | 470 | 4 | 40 |
| 2216 | 16mm | 1W | Aluminum | Amber | 595 | 8.5 | 40 |
| 3192 | 16mm | 1W | Aluminum | UV | 410 | 0.25 | 40 |
| 3497 | 11mm | 3W | Aluminum | Cool White | 9000K+ | 75 | 60 |
| 3498 | 11mm | 3W | Aluminum | Neutral White | 6000-6500K | 75 | 60 |
| 3499 | 11mm | 3W | Aluminum | Warm White | 3000-3200K | 75 | 60 |
| 3500 | 11mm | 3W | Aluminum | Red | 625 | 35 | 80 |
| 3502 | 11mm | 3W | Aluminum | Green | 525 | 80 | 45 |
| 3501 | 11mm | 3W | Aluminum | Blue | 470 | 12 | 60 |
| 3503 | 11mm | 3W | Aluminum | Amber | 595 | 25 | 70 |
| 3504 | 11mm | 3W | Aluminum | UV | 410 | 0.25 | 65 |
| 3465 | 11mm | 1W | Stainless Steel | Cool White | 9000K+ | 20 | 40 |
| 3467 | 11mm | 1W | Stainless Steel | Warm White | 3000-3200K | 20 | 40 |
| 3468 | 11mm | 1W | Stainless Steel | Red | 625 | 10 | 40 |
| 3469 | 11mm | 1W | Stainless Steel | Blue | 470 | 3 | 40 |
| 3470 | 11mm | 1W | Stainless Steel | Green | 525 | 15 | 40 |
| 3471 | 11mm | 1W | Stainless Steel | Amber | 595 | 7.5 | 40 |
Frequently Asked Questions
If your LED Bolt is too bright, you can always dim it down with a resistor.
You can experiment with a number of different resistors until you find a suitable brightness.
To start, we'd recommend ordering about 5 of the 1/2 Watt, 560 Ohm resistors.
You can then try wiring anywhere from 1 to 5 (or even more if you want) in series.
You can connect them to either the positive or negative wire.
It won't reduce nor damage the life of the LED. If anything, it should increase it slightly.
Here's a quick video to show how you can use the resistors:
You can experiment with a number of different resistors until you find a suitable brightness.
To start, we'd recommend ordering about 5 of the 1/2 Watt, 560 Ohm resistors.
You can then try wiring anywhere from 1 to 5 (or even more if you want) in series.
You can connect them to either the positive or negative wire.
It won't reduce nor damage the life of the LED. If anything, it should increase it slightly.
Here's a quick video to show how you can use the resistors:
The nuts on the 6mm bolt is sooooo tiny. it's easy to miss.
So here's a photo to show you where to look for it.
And please be careful not to overtighten it - this could break the flange which is somewhat delicate.
Customer questions & answers
Why are the 6mm bolts listed as 1 watt while in the specifications it says they are 18mA @ 12vdc which is actually .21 watts?
The COB chip on a 6mm LED bolt is a 1W chip, means ideally it can be powered up to 1W. We intentionally lower the operating wattage for the 6mm LED bolt to play safe because it can't withstand heat generated at full power unless it is mounted to a big heat sink for heat dissipation.
I need to mount on a radius surface for use as 3rd brake lights on a custom build (2" pipe). Do you have a mounting surface that has a radius or all of then a flat mounting surface?
Please call Customer Service for assistance with this question.
Why a 2 of my 4 cool white led bolts has turned white solid after a month of use, same intensity but pure white?
Please contact Customer Service at 800-245-8131.
Customer Reviews
451 Reviews
Perfect little light
Jason Temple from Modesto, CA
Black led bolt light came looking just like I wanted. Using in my car as accent / custom fog lights. I give 5 stars lights are high quality and no issues so far.
Perfect fit
Vicki L Taylor from Melbourne, FL
I bought these LED bolt light to install in the center of an amber light
For my outside mirror lights. They worked amazingly.
Great product but one light failed already.
Alan Burke from College Park, MD
Love the 11mm lights, however one of the six that I purchased and installed on my truck has failed already. It's not a wiring problem. It's only been a month since my install so I'm waiting to see if any others blow before I replace the dead light. Otherwise, this has been an awesome product. Gave 3 stars only because of failure on 1 of 6.
Oznium LED bolts
Darren DeYoung from Prescott, AZ
Great product, making it easy for lighting support in a small format. Wiring and hardware of excellent quality. Light output great. Very satisfied with the product.
Great product
Ian Nadeau from Kamloops, Canada
Easy to use, high quality product would recommend these LEDs to anyone
Extremely satisfied
Geoff Rood from Detroit Metro
To begin, I was pleased with the amount of technical information Oznium had available about their lighting solutions, as well as the variety of solutions in the LED bolt selection. The flush mount LED bolts arrived quickly and well packaged, with double threaded nuts as well as spring clips (which I wasn't expecting). Dimensions matched the technical drawings available perfectly, so no surprises there. The lights themselves work great. The long wiring lead will allow extra flexibility for wiring.
Perfect amount of light!!
Christopher Fergen from Sioux City, IA
Installed 2 Bolt LEDs 1w, no lens, Neutral white in the upper trim panel of our 21 Subaru Ascent for added cargo compartment light. The factory light is low on the side and offers very little light. These bolt lights give a nice even spread of light with little to no shadowing. The light color is perfect! a nice white with zero blue to it. I know 33 lumens doesn't sound like much, but it's just right. Not enough to blind you, but more than enough light to be usable. This is one of the few bolt lights that do not have a lens which is awesome!! With a lens it tends to have focused beam rather than a nice even spread of light. Keep making these!!!
Awesome flush Mount Leds
Phuong Le from Port Orange, FL
Amber color was perfect for my project I did on my truck.. excellent product...
Flush Mount LED Bolt
Derek Righter from Irvine, CA
Lights are very cool will be ordering more!!!
Vibrating off motorbike
Marcel vK from Netherlands
11mm stainless steel 3W red.
Light output is really good. even so bright i needed to dim it with a resistor. I'm using it as an additional taillight next to my stock taillight on my motorbike.
The bolt is an 11mm fine thread. This is a bit troublesome as the nuts supplied with the bolt are round with a knurling on the outer diameter.
Nice to fit with your hands but its not possible to put a pliers or wrench to apply a good amount of force and tie down the bolt properly.
I would prefer a M10 (metric) tread as then i could mount with an M10 nut and tie the bolt down properly.
ive had to add a liquid treadlock to keep the supplied rings from vibrating off.